View LD39015XX08_255338.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LD39015XX08 - LD39015XX10 LD39015XX12 - LD39015XX33
150 mA low quiescent current low noise voltage regulator
www..com
Features

Input voltage from 1.5 to 5.5 V Ultra low dropout voltage (80 mV typ. at 100 mA load) Very low quiescent current (18 A typ. at no load, 35 A typ. at 150 mA load, 1 A max in off mode) Very low noise without bypass capacitor (29 VRMS at VOUT = 0.8 V) Output voltage tolerance: 2.0% @ 25 C 150 mA guaranteed output current Wide range of output voltages available on request: 0.8 V to 3.3 V with 100 mV step Logic-controlled electronic shutdown Compatible with ceramic capacitors COUT = 1 F Internal current and thermal limit Available in SOT666 and SOT23-5L packages Temperature range: -40 C to 125 C from 1.5 V to 5.5 V with a typical dropout voltage of 80 mV. It is stable with ceramic capacitor. The ultra-low drop voltage, low quiescent current and low noise features make it suitable for low power battery-powered applications. Power supply rejection is 65 dB at low frequencies and starts to roll off at 10 kHz. Enable logic control function puts the LD39015XX in shut-down mode allowing a total current consumption lower than 1 A. The device also includes short-circuit constant current limiting and thermal protection. Typical applications are mobile phones, personal digital assistants (PDAs), cordless phones or similar battery-powered systems.
SOT666 SOT23-5L

Description
The LD39015XX series provides 150 mA maximum current from an input voltage ranging Table 1. Device summary
Order codes
Output voltage SOT666 LD39015XG08R LD39015XG10R
(1)
SOT23-5L LD39015M08R (1) LD39015M10R LD39015M12R LD39015M15R LD39015M18R LD39015M25R
(1) (1) (1)
0.8 V 1.0 V 1.2 V 1.5 V 1.8 V 2.5 V 3.3 V
LD39015XG12R (1) LD39015XG15R LD39015XG18R LD39015XG25R
(1) (1) (1)
LD39015XG33R
LD39015M33R (1)
1. Available on request. Other voltages available on request from 0.8 V to 3.3 V in 100 mV step.
April 2008
Rev 2
1/16
www.st.com 16
Contents
LD39015XX08 - LD39015XX10 - LD39015XX12 - LD39015XX33
Contents
1
www..com
Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2
3 4 5 6 7 8
2/16
LD39015XX08 - LD39015XX10 - LD39015XX12 - LD39015XX33
Diagram
1
Figure 1.
Diagram
Block diagram
www..com
IN
OUT
BandGap 1.22 V
R1 Trimming
Thermal Protection
R2
Enable EN GND
3/16
Pin configuration
LD39015XX08 - LD39015XX10 - LD39015XX12 - LD39015XX33
2
Figure 2.
www..com
Pin configuration
Pin connection (top view)
SOT666
SOT23-5L
Table 2.
Pin description
Pin n Symbol Function Enable pin logic input: Low=shutdown, High=active Common ground. Input voltage of the LDO Output voltage Not connected Not connected
SOT666 1 2 3 4 5 6
SOT23-5L 3 2 1 5 4 -EN GND IN OUT NC NC
4/16
LD39015XX08 - LD39015XX10 - LD39015XX12 - LD39015XX33
Typical application
3
Figure 3.
www..com
Typical application
Typical application circuit
VIN 1 F
IN
OUT 1 F
VOUT Load
VEN
EN
GND
5/16
Maximum ratings
LD39015XX08 - LD39015XX10 - LD39015XX12 - LD39015XX33
4
Table 3.
Symbol
www..com
Maximum ratings
Absolute maximum ratings
Parameter DC input voltage DC output voltage Enable input voltage Output current Power dissipation Storage temperature range Operating junction temperature range Value -0.3 to 7 -0.3 to VI + 0.3 -0.3 to VI + 0.3 Internally limited Internally limited -65 to 150 -40 to 125 Unit V V V mA mW C C
VIN
VOUT VEN IOUT PD TSTG TOP
Note:
Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. All values are referred to GND. Thermal data
Parameter Thermal resistance junction-ambient Thermal resistance junction-case SOT23-5L 255 81 SOT666 132 56 Unit C/W C/W
Table 4.
Symbol RthJA RthJC
6/16
LD39015XX08 - LD39015XX10 - LD39015XX12 - LD39015XX33
Electrical characteristics
5
Table 5.
Symbol www..com VIN VUVLO
Electrical characteristics
Electrical characteristics (TJ = 25 C, VIN = VOUT(NOM) + 1 V, CIN = COUT = 1 F, IOUT = 1 mA, VEN = VIN, unless otherwise specified) (1)
Parameter Test conditions Min. 1.5 1.45 1.30 VOUT > 1.5V, IOUT = 1mA, TJ = 25C VOUT > 1.5V, IOUT = 1mA, -40C < TJ < 125C VOUT 1.5V, IOUT = 1mA VOUT 1.5V, IOUT = 1mA, -40C < TJ < 125C -2.0 -3.0 10 30 0.01 10 0.002 40 80 29 100 mV 1.35 2.0 % 3.0 Typ. Max. 5.5 1.48 Unit V V mV
Operating input voltage Turn-on threshold Turn-off threshold
VOUT
VOUT accuracy
VOUT VOUT VOUT VOUT VDROP eN
Static line regulation Transient line regulation (2) Static load regulation Transient load regulation (2) Dropout voltage (3) Output noise voltage
VOUT +1V VIN 5.5V, IOUT = 1mA VIN = +500mV, IOUT = 1mA, TR = TF = 5s IOUT = 1mA to 150mA IOUT = 1mA to 150mA, TR = TF = 5s IOUT = 100mA, VOUT > 1.5V -40C < TJ < 125C 1.1kHz to 100kHz, IOUT = 10mA, VOUT = 0.8V VIN = VOUTNOM + 0.5V +/-VRIPPLE VRIPPLE = 0.1V, Freq. = 1kHz IOUT = 10mA VIN = VOUTNOM + 0.5V +/-VRIPPLE VRIPPLE = 0.1V, Freq.=10kHz IOUT = 10mA IOUT = 0mA IOUT = 0mA, -40C < TJ < 125C IOUT = 0 to 150mA
%/V mVpp %/mA mVpp mV VRMS
65 dB 62 18 50 38 A 70 0.001 350 0.4 0.9 0.1 100 1 mA V V nA 7/16
SVR
Supply voltage rejection VOUT = 1.5V
IQ
Quiescent current
IOUT = 0 to 150mA -40C < TJ< 125C VIN input current in OFF MODE: VEN = GND
ISC
Short circuit current Enable input logic low
RL = 0 VIN = 1.5V to 5.5V, -40C < TJ < 125C VIN = 1.5V to 5.5V, -40C < TJ < 125C VEN = VIN
VEN Enable input logic high IEN Enable pin input current
Electrical characteristics Table 5.
Symbol TON
LD39015XX08 - LD39015XX10 - LD39015XX12 - LD39015XX33
Electrical characteristics (continued) (TJ = 25 C, VIN = VOUT(NOM) + 1 V, CIN = COUT = 1 F, IOUT = 1 mA, VEN = VIN, unless otherwise specified) (1)
Parameter Turn on time
(4)
Test conditions
Min.
Typ. 30 160
Max.
Unit s C
Thermal shutdown TSHDN www..com Hysteresis Output capacitor Capacitance (see typical performance characteristics for stability) 1
20 22 F
COUT
1. For VOUT(NOM) < 1.2 V, VIN = 1.5 V 2. All transient values are guaranteed by design, not production tested 3. Dropout voltage is the input-to-output voltage difference at which the output voltage is 100 mV below its nominal value. This specification does not apply for output voltages below 1.5 V 4. Turn-on time is the time measured between the enable input just exceeding VEN High Value and the output voltage just reaching 95 % of its nominal value
8/16
LD39015XX08 - LD39015XX10 - LD39015XX12 - LD39015XX33Typical performance characteristics
6
Figure 4.
0.85 0.84 www..com 0.83 0.82 0.81 0.8 0.79 0.78 0.77 0.76 0.75 -50 VOUT [V]
Typical performance characteristics
Output voltage vs temperature
IOUT=1mA IOUT=100mA
VOUT[V]
Figure 5.
0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 0
Output voltage vs input voltage
VIN=1.5V
VIN=1.5V
0
50 Temp [C]
100
150
1
2
3 VIN [V]
4
5
6
Figure 6.
0.16 0.14 0.12 0.1 0.08 0.06 0.04 0.02 0 0
Dropout voltage vs output current
Figure 7.
2.4 ESR @ 100 KHz [Ohm] 2.1 1.8 1.5 1.2 0.9 0.6 0.3 0 0
COUT stability region
CIN=1 F, VIN=VEN=1.5 to 5.5 V IOUT=1 mA to 0.15 A
Vdropout [V]
STABILITY REGION
0.05
0.1
0.15
0.2
0.25
IOUT [A]
5 10 15 20 COUT [F] (nominal value)
25
Figure 8.
Supply voltage rejection vs frequency
Figure 9.
Output noise voltage vs frequency
75 70 65 60 55 50 45 40 35 30 25 20 15 10 100
800
IOUT=10 mA, VIN=4.3 V, CIN=COUT= 1F
700
VOUT=3.3 V
600 500
SVR [dB]
nV/Hz
IOUT = 10mA Vripple = 0.1Vpp
400 300 200 100
1000
10000 Freq [Hz]
100000
0 1000
10000
100000
FREQ [Hz]
9/16
Typical performance characteristicsLD39015XX08 - LD39015XX10 - LD39015XX12 - LD39015XX33
Figure 10. Quiescent current vs input voltage Figure 11. Load transient
100
www..com
80 60 40 20
Iq [A]
VIN=VINH, CIN=COUT=1F, IOUT=0.15A
0 1.4 1.9 2.4 2.9 3.4 3.9 4.4 4.9 5.4 5.9 VIN[V]
VEN = VIN = 1.5V, IOUT = 1mA to 0.15A, CIN = COUT = 1F, tr = tf = 5s
Figure 12. Line transient
Figure 13. Enable transient
VIN = VEN = 1.5 to 5.5V, IOUT = 1mA, COUT = 1F, tr = tf = 5s
VIN = 1.5V, VEN = 0 to 1V, IOUT = 1mA, CIN = COUT = 1F
10/16
LD39015XX08 - LD39015XX10 - LD39015XX12 - LD39015XX33
Package mechanical data
7
Package mechanical data
In order to meet environmental requirements, ST offers these devices in ECOPACK(R) packages. These packages have a lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com.
www..com
11/16
Package mechanical data
LD39015XX08 - LD39015XX10 - LD39015XX12 - LD39015XX33
SOT23-5L mechanical data
mm. Dim.
www..com
mils. Max. 1.45 0.10 1.30 0.50 0.20 3.00 1.75 Min. 35.4 0.0 35.4 13.7 3.5 110.2 59.0 37.4 3.00 0.60 102.3 3.9 118.1 23.6 Typ. Max. 57.1 3.9 51.2 19.7 7.8 118.1 68.8
Min. 0.90 0.00 0.90 0.35 0.09 2.80 1.50
Typ.
A A1 A2 b C D E e H L
0.95 2.60 0.10
7049676D
12/16
LD39015XX08 - LD39015XX10 - LD39015XX12 - LD39015XX33
Package mechanical data
SOT666 mechanical data
mm. Dim.
www..com
inch. Max. 0.60 0.18 1.70 1.70 1.30 0.26 0.30 Min. 0.021 0.005 0.059 0.059 0.043 0.004 0.004 0.002 0.25 0.17 0.27 0.5 0.2 Typ. 0.022 0.006 0.065 0.065 0.047 0.007 0.009 0.004 0.25 0.34 Max. 0.024 0.007 0.067 0.067 0.051 0.010 0.012
Min. 0.53 0.13 1.50 1.50 1.10 0.11 0.10 0.05 0.17
Typ. 0.57 0.17 1.66 1.65 1.20 0.19 0.23 0.10
A A3 D E E1 L1 L2 L3 b b1 e e1
0.27 0.50 0.20 8 10
0.34
12
8
10
12
7673701C
13/16
Package mechanical data
LD39015XX08 - LD39015XX10 - LD39015XX12 - LD39015XX33
Tape & reel SOT23-xL mechanical data
mm. Dim.
www..com
inch. Max. 180 Min. Typ. Max. 7.086 0.504 0.795 2.362 14.4 0.567 0.123 0.120 0.050 0.153 0.153 0.127 0.124 0.054 0.157 0.157 0.131 0.128 0.0.58 0.161 0.161 0.512 0.519
Min.
Typ.
A C D N T Ao Bo Ko Po P 3.13 3.07 1.27 3.9 3.9 3.23 3.17 1.37 4.0 4.0 12.8 20.2 60 13.0
13.2
3.33 3.27 1.47 4.1 4.1
14/16
LD39015XX08 - LD39015XX10 - LD39015XX12 - LD39015XX33
Revision history
8
Table 6.
Date
Revision history
Document revision history
Revision 1 2 Initial release. Modified: Table 5 on page 7. Changes
www..com 13-Nov-2007
11-Apr-2008
15/16
LD39015XX08 - LD39015XX10 - LD39015XX12 - LD39015XX33
www..com
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
(c) 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
16/16

▲Up To Search▲

Price & Availability of LD39015XX08

	To Download LD39015XX08 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .